20 Fun Facts About Fiat 500 Replacement Key Cost

Fiat 500 Replacement Key Fob

If your remote key fob isn't working, it may be time to replace the battery. If you replace the battery but it's still not working it could be the issue elsewhere.

United Locksmith specializes in the production of new keys for classic automobiles. We have the tools and parts required for this type of service.

Dead Coin Battery

The most frequent reason why your Fiat 500 key fob will not lock or unlock the doors is a dead battery. The battery inside the key fob will drain quickly in the event that you don't use frequently enough. If your remote has started to show signs of a loss of range, or has stopped functioning or not responding, then the battery could be dead.

The battery inside the key fob is held in place with metal clips for retaining. If the clips are not tightly secured, they could result in problems with contact that can prevent the remote from receiving power. Use a flathead screwdriver to open the retaining clips and remove the old battery. Make sure that the battery you choose to use has the same voltage, size and specification as the original.

The key fob can also be damaged or corroded by exposure to water. Even a short bath in soapy water could cause damage to the electronic chip inside. It is best to keep your key fob in a dry place.

Water Damage

Damage to your water supply could be the reason behind your key fob not working properly. Key fobs have rubber seals to protect them from being damaged by rain or a splash of water. However, it is crucial to keep your car keys out of the pool, ocean and the washing machine!

The key fob comes with an electronic chip that sends an immobilizer system of your vehicle. The chip is what allows the 500 to lock and start. If it gets wet, however it will cease to work.

You can clean the inside electronics of your keyfob with isopropyl alcohol or an electronic cleaner to determine whether they're still working. However, it's better to purchase a replacement from a dealer instead of trying to fix the key fob that is submerged in salt water.

A replacement fob can cost you a little bit however it's much less expensive than paying to have your fiat van key replacement 500 towed to a dealer and repaired there! Plus, you can do it yourself with a few easy steps. Make sure you have the correct battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob communicates directly with the immobiliser in your car to ensure that your vehicle will only start once the right keys are in place. If the chip is damaged, or damaged in any way, your car will not start.

Water damage or a dead cell phone battery are the most frequently cited reasons for the chip being damaged. Regardless of the reason, it's a good idea to leave the job to a locksmith, as they will be able to repair the chip fast and at a low cost.

If your key fob will not function after exposure to clean water from a tap or rain take the battery off. Wipe down the electronic component with a towel. If the key fob still doesn't work it's most likely a fried chip and must be replaced.

A few people turn to their dealer when they are in need of a new Fiat key fob, however it can be a costly alternative. If you're seeking a cost-effective solution to get your Fiat key fob repaired Look no further than United Locksmith. We have the tools and knowledge needed to repair your fiat punto replacement key key fob (cheaperseeker.Com) in a quick and professional way.

Faulty Receiver Module

Fiat key fobs transmit a signal to the vehicle which will unlock and close doors (and start the car for vehicles with an automatic transmission) up to 50 feet. However there are several things that could cause the fob to stop functioning. This could be due to a dead battery or water damage, worn-out buttons, a receiver issue, signal interference or malfunctioning chips.

If the fob was located in the pocket that has been subject to severe trauma (such as being dropped on a hard floor or being washed in the washing machine), it may not be in a position to connect with the Body Control Module (BCM) of the vehicle. This is because the BCM is secured and will only accept a signal from a genuine key and not another.

You will need to replace the fob in case this happens. A professional locksmith will handle the entire key replacement process including programming a brand new key for your 500. In fact, they could offer you a clone key that functions exactly the same as the original fob (and costs a fraction of the cost).